Boat Parts

This is a used Carburetor pulled from a 1990 140hp 3.0 Mercruiser engine. Choke is cracked loose and the bottom base has some rust in the barrels a...

This is a complete drive unit assembly. Pulled from a 1990 Dynasty with a 3.0 Alpha Drivetrain SN #D402441 LOCAL PICK-UP ONLY or possibly strapped...

Recent pull from a 1989 Larson, Complete but both have a crack and scratches, see photos Track Page Views WithAuctiva's Counter

Good Used Condition

Complete Dash panel pulled from an 16ft 1990 Dynasty Elan. NO KEY. wiring harness to engine plug for a 3.0 Mercruiser Alpha Drive as shown

Recent pull from a 1990 Dynasty with a running 3.0 Mercruiser engine.

Boat steering wheel as shown from a 1990 4Winns 170 Freedom, tapered keyed shaft type,

...

Recent pull from a 1981 OMC Stringer 800 Drive with a 3.8L v6 motor. Was a working unit. Marked as 1.77:1

Recent pull from a 1985 4Winns. Ignition switch with key, Blower, Accessory, Bilge pump, Navigation/Anchor Lights, Horn. switch rough openings are ...

Recent pull from a good running 1986 Bayliner 2.1 with a 270 Outdrive

Recent pull from a good running 1986 Bayliner Capri  AQ131A Engine with a 270 Outdrive Fresh Water Used Only. Good condition. Complete as shown. O...

Recent pull from a working 1981 Viking Deck Boat 3.8 V6 Engine and an OMC 800 outdrive. Spins smooth, oil drained was clean. Skeg has some damage a...

Recent pull from a 1985 4Winns with a running 3.0 140hp Mercruiser engine.

Boat steering wheel as shown, tapered keyed shaft type, some flecks of what looks like overspray as shown

Chromed metal gas cap and collar. Pulled from a 1960's Larson. chain tether not attached

Recent pull from a 1980 Deck boat. Trimmed to fit rough opening of 14.5" by 2.0". Outside trim dimensions 17.25" by 2.5" Track Page Views WithA...

Working pull from and older fishing boat 2.25" diameter

Recent pull from a 1986 4Winns Mercruiser  Alpha One Outdrive . Complete and Free moving, worked good and wiring harness, side mount.  Track Page...

Recent pull from a 1985 4Winns Mercruiser  Alpha One Outdrive . Complete and Free moving, worked good and wiring harness, side mount.  Track Page...

Thought I would offer it whole before parting it out. It was in very good condition until a rodent found its way into a cylinder. Was a strong run...

Recent working pull from a 1981 OMC Stringer 800

Recent working pull from a 1984 OMC Stringer 400

Recent pull from a 1987 Four Winns with an Alpha One outdrive. Good working order

Recent pull from a good running 1988 2.3 OMC engine. 

Recent pull from a running 1979 Chrysler Outboard 70HP Skier

Recent pull from a running 1979 Chrysler Outboard.

Boat steering wheel as shown from a 1986 4Winns 160 Freedom, tapered keyed shaft type,

This is the wiring harness, clipped at the gauges running back to the engine harness plug as shown for a 5.0 Ford OMC Cobra Engine

Boat steering wheel as shown from a 1987 4Winns 160 Freedom, tapered keyed shaft type,

Drivers Right front side glass panel pulled from an 19ft 1989 Bayliner Capri

Recent pull from a running 1962 Evinrude 40hp Outboard. 27'5" in length

Drivers Right rear side glass panel pulled from an 19ft 1989 Bayliner Capri

Recent pull from a running 1979 Chrysler Outboard. good teeth

Used Prop with Edge Wear but still very good. Heavy Stainless Steel

Recent pull from a good running 1990 2.3 OMC Cobra outdrive 

Recent pull from a 1986 4Winns with a running 3.0 140hp Mercruiser engine with shifter on rocker cover.

Recent pull from a running 1989 Bayliner

Recent pull from a 1985 Four Winns 19ft with a 3.0 Mercruiser and Alpha One outdrive.

Passenger Left rear side glass panel pulled from an 19ft 1989 Bayliner Capri 5.0

Recent pull from a 1959 Johnson. Clean but I would still go through it

Recent pull from a good running 1988 2.3 OMC engine.

Boat steering wheel as shown, tapered keyed shaft type, no center logo on center cap

Drivers front glass panel pulled from an 19ft 1989 Bayliner Capri

Recent pull from 4.3 Mercruiser 2BBL. Small surface rust spot on inside of pan as shown. No rust on outside

Recent working pull from an OMC Cobra with a 1989 5.0 powertrain. Track Page Views WithAuctiva's Counter

Recent pull from a 1974 50hp Johnson Outboard. Fits many years and models

Recent pull from a running 1992 4.3 GM Mercruiser Engine